Differences

This shows you the differences between two versions of the page.

Link to this comparison view

eleksegg [2019/05/08 02:35] (current)
eleksmaker [EleksEgg]
Line 1: Line 1:
 +======▧EleksEgg======
  
 +---
 +
 +## Assembly & Connection
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E7%BB%84%E8%A3%85%E6%8E%A5%E7%BA%BF%E6%95%99%E7%A8%8B.jpg}}
 +
 +## Operating Instructions
 +**[[http://​wiki.eleksmaker.com/​doku.php?​id=elekscam|DownLoad EleksCAM v3.1]]**
 +
 +1.Connect the usb cable and power supply first.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E8%BF%9E%E6%8E%A5.jpg}}
 +
 +2.Open the EleksCAM Software.
 +
 +3.Click the button on the right-top of EleksCAM and then click install driver.(only need install once)
 +
 +4.Close EleksCAM.
 +
 +5.Open Device Manager to find the serial port number.
 +
 +6.Open Elekscam and then choose the right serial port number.
 +
 +7.EleksCAM will show connect success (Find Serial Ports Successful COMx).
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E5%AE%89%E8%A3%85%E9%A9%B1%E5%8A%A8.gif}}
 +
 +8.Click Select Machine and then choose EleksEgg , and messagebox will showed “Switch To EleksEgg Mode Successful” if  operation Successful.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E9%80%89Egg.gif}}
 +
 +9.Turn on the controller board power switch.
 +
 +10.Trim servo arm.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E4%BF%AE%E5%89%AA%E8%88%B5%E6%9C%BA%E8%87%82.jpg}}
 +
 +11. Set Servo angle 20 degree, click [Laser ON]/[Laser Off] to watch the moving range, assemble arm as shown.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E8%88%B5%E6%9C%BA%E8%87%82%E5%AE%89%E8%A3%85.gif}}
 +
 +12. Clip the egg and put down pen holder, Click [Laser ON]/[Laser Off] and tune position of pen as shown.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E7%AC%94%E5%AE%89%E8%A3%85.gif}}
 +
 +13.Set step movement to 10mm , manually click arrow to move machine to central point , and then click Set Home.
 +
 +14.Click Gallery to choose the picture , double click the target picture , modify the Acreage/​Speed/​Mode (Suggest to choose Outline) , and then click generate. ​ (if there is an error , please ignore)
 +
 +15.Click Start to drawing.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​Egg%E6%93%8D%E4%BD%9C.gif}}
 +
 +Draw complete
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksEgg/​%E7%94%BB%E8%9B%8Bing.gif}}
 +
 +## Frequently Asked Questions
  • Show page