Differences

This shows you the differences between two versions of the page.

Link to this comparison view

eleksdrawpro [2019/05/08 02:47] (current)
eleksmaker created
Line 1: Line 1:
 +======EleksDraw Pro======
  
 +
 +## Assembly & Connection
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksDrawPro/​%E7%BB%84%E8%A3%85%E6%8E%A5%E7%BA%BF%E6%95%99%E7%A8%8B.jpg}}
 +
 +## Operating Instructions
 +**[[http://​wiki.eleksmaker.com/​doku.php?​id=elekscam|DownLoad EleksCAM v3.1]]**
 +
 +1.Connect the usb cable and power supply first.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksDraw/​%E8%BF%9E%E6%8E%A5%E6%95%B0%E6%8D%AE%E7%BA%BF.gif}}
 +
 +2.Click the button on the right-top of EleksCAM and then click install driver.(only need install once)
 +
 +3.Close EleksCAM.
 +
 +4.Open Device Manager to find the serial port number.
 +
 +5.Open Elekscam and then choose the right serial port number.
 +
 +6.EleksCAM will show connect success (Find Serial Ports Successful COMx).
 +
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksDraw/​%E5%AE%89%E8%A3%85%E9%A9%B1%E5%8A%A8.gif}}
 +
 +
 +8.Click Select Machine and then choose EleksDraw , and messagebox will showed “Switch To EleksDraw Mode Successful” if  operation Successful.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksDraw/​%E9%80%89%E6%8B%A9EleksDraw.gif}}
 +
 +9.Turn on the controller board power switch.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksDraw/​%E6%89%93%E5%BC%80%E7%94%B5%E6%BA%90.gif}}
 +
 +10.Clip the Pen and put down paper , Set Servo angle 20 degree, click [Laser ON]/[Laser Off] and tune position of pen as shown.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksDraw/​%E8%B0%83%E8%8A%82%E7%AC%94.gif}}
 +
 +11.Check[X-REV] and [Y-REV],Set step movement to 10mm , manually click arrow to move machine to central point , and then click Set Home.
 +
 +12.Click Gallery to choose the picture , double click the target picture , modify the Acreage/​Speed/​Mode (Suggest to choose Outline) , and then click generate. ​ (if there is an error , please ignore)
 +
 +13.Click Start to drawing.
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksDraw/​%E6%93%8D%E4%BD%9C.gif}}
 +
 +## Frequently Asked Questions
  • Show page