Differences

This shows you the differences between two versions of the page.

Link to this comparison view

faq [2018/04/17 08:47] (current)
Line 1: Line 1:
 +====== Frequently Asked Questions ======
 +\\
 +
 +
 +#Question : How To Focus The Laser ?
 +
 +###First , you need press the weak light button which is on the top of laser. And then keep rotate the nuts until get the minimun point. ​
 +
 +
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksLaserA3X/​laserfocus.png}}
 +
 +\\
 +
 +#Question : Which Software Should I Choose ?
 +###When you get our EleksLaser Machine , the main controller board "Mana SE" has already flashed EleksROM version 1.3 Firmware . So we recommend use our offical software "​EleksCAM"​ . And if you want to use another software to carving , you can try T2Laser or BenBox to carving.
 +
 +**[[http://​wiki.eleksmaker.com/​doku.php?​id=elekscam|DownLoad EleksCAM Release ​ v3.1.0 v]]**
 +
 +**[[http://​forum.eleksmaker.com/​category/​13/​t2-laser-%E4%B8%A8cooperative-partner|DownLoad T2Laser Release]]**
 +
 +**[[http://​wiki.eleksmaker.com/​doku.php?​id=benbox|DownLoad BenBox Release]]**
 +
 +\\
 +
 +#Question : Why When I Use EleksCAM , I Can Move XY Motor manually But Cant Normal Carving?
 +###Some customs may have different font setting in windows system , so that may cause elekscam cant send command normally . To solve this problem you need open your system control panel and then click change Time Clock And Region Like This:
 +
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​forum/​308d869e-6034-4733-b4be-c52d07843771.png}}
 +
 +\\
 +
 +#Question : I Use BenBox In The Past , But Now I Want To Use EleksCAM , What Should I Do ?
 +###Due to the BenBox and EleksCam use the different software , so you need reflash the firmware and rewrite the settings , luckily we got EleksROM Auto Flash Software for you , you just need following this page to reflash the firmware
 +
 +**[[http://​wiki.eleksmaker.com/​doku.php?​id=eleksrom|DownLoad EleksROM Release ​ v3.8.0 v]]**
 +
 +\\
 +
 +#Question : How To Move Machine Manually With EleksCAM ?
 +###
 +Please connect you machine first and then click the direction arrow once to move machine . PS: 1 means 1mm per click
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksLaserA3X/​elekscam.png}}
 +
 +\\
 +
 +#Question : How To Install Driver With EleksCAM?
 +###
 +Just Click the button on the top of EleksCAM and then Click Install Driver
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksLaserA3X/​installdriver.png}}
 +
 +\\
 +
 +#Question : When I Click X+/Y+ But X Axis Goes X-/Y-
 +###
 +You need reverse the relevant Axis (X-Rev means reverse X Axis) . Just Click the relevant Axis and then Click Save Button
 +{{http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​EleksLaserA3X/​rev.png}}
 +
 +\\
 +
 +#Question : I Want To Know How To Set Pluse/​Accel/​Speed
 +###
 +
 +  EleksLaser ​ Default: 80/80/Laser Mode/XY Machine Mode //x,y Pluse step/mm /Model /Machine Type
 +  EleksDraw ​  ​Default:​ 100/​100/​Servo Mode/CoreXY Machine Mode //x,y Pluse step/mm /Model /Machine Type
 +  EleksEgg ​   Default: 20/20/Servo Mode/XY Machine Mode //x,y Pluse step/mm /Model /Machine Type
 +  EleksMill ​  ​Default:​ 400/​400/​400/​Laser Mode/XY Machine Mode //x,y,z Pluse step/mm /Model /Machine Type
 +
 +`All Machine Default Acceleration is 200 (but it can up to 500~1000)`
 + 
 +`And For Speed/Laser Power is depend on your needed`
 +  ​
 +\\
 +
 +
 +
 +
  
  • Show page