Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
extra_module [2019/03/06 08:12]
eleksmaker
extra_module [2019/03/06 08:45] (current)
eleksmaker
Line 1: Line 1:
 +======▧EleksLaser Extra Moduel======
  
 +--- 
 +
 +##Firmware Instruction
 +
 +---
 +
 +**First , [[http://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​EleksRom_Pro_2.1.zip|Click here to download the EleksRom_Pro_2.1]]
 +**
 +
 +Unzip the `EleksRom_Pro_2.1.zip`
 +
 +Connect your `EleksLaser A3` to compurter then Click `EleksRom_Pro.exe`
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​1.png}}
 +
 +--- 
 +
 +
 +**If your MansSE are using EleksRom V3.7** ​
 +
 +First , after open `EleksRom_Pro.exe` , please choose your machine `serial port`.
 +
 +Then choose firmware to `Grbl_v1.1` , and click Flash , waitting for it finished
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​5.png}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​6.png}}
 +
 +---
 +
 +**If your MansSE are using GRBL 1.1**
 +
 +First , after open `EleksRom_Pro.exe` , please choose your machine `serial port`.
 +
 +Then choose firmware to `Settings_Clear` , and click Flash , waitting for it finished and hold on for about 10 second.
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​2.png}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​3.png}}
 +
 +You dont need plug out your `ManaSe` , and then choose firmware to `Grbl_v1.1` , Flash again and waitting for it finished.
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​5.png}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​6.png}}
 +
 +---
 +
 +##Assembly & Connection
 +
 +**Our recommand limit switchs install location is  one the machine `TOP` `RIGHT`**
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​19.jpg}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​10.jpg}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​11.jpg}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​12.jpg}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​13.jpg}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​14.jpg}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​15.jpg}}.
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​16.jpg}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​17.jpg}}
 +
 +--- 
 +
 +##Software Instruction
 +
 +---
 +
 +Now , you can open your `Control software` , like EleksCAM/T2 Laser/​Candel
 +
 +**If you are not following our recommand limit switchs install direction. you need change your Setting like this :**
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​7.png}}
 +
 +---
 +
 +**When first time you install switch or trigger switch when moving axis , your controller board will become into `LOCK` mode**
 +
 +you need type Gcode `$x` to unlock machin like this.
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​8.png}}
 +
 +then use Gcode `$H` to start Homing cycle.
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​9.png}}
 +
 +---
 +
 +# Here are the advanced settings
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​20.png}}
 +
 +{{https://​eleksmakeross.oss-ap-southeast-1.aliyuncs.com/​wiki/​ExtraModule/​21.png}}
 +
 +---
  • Show page