EleksROM丨V3.8.0 Release 3.27.2017

Brand New CoreXY/XY 丨 Laser/Servo Mode Easy Switch Firmware Release


From 3 month ago , we start to upgrade our EleksLaser Desktop Engraving Machine and use brand-new Mana SE Controller.

Cause we have various Desktop Engraving or Draw Machine , So when you get our product with Mana SE Controller ,

you need to Set Paramto Mana SE Controller.

And Now We Have Full AutoMactic Upgrade And Set Param SoftWare Called EleksROM For You.

Please Attention - The Following Controller  Support This SoftWare
Supported Controller:
EleksMaker Mana SE Controller  (V1.3/V2.1 Default Is V2.1 With No Version String On It)
EleksMaker Mana Controller  (V2.1)



First Step: Click Here To Download EleksROM V3.8

When Download is accomplished , Click EleksROM.zip To UnZip it.

Then you can click on EleksROM.exe to directly Run or right click on EleksROM.exe to make a Shotcut to desktop

Please Attention : Please Inset Your EleksMaker Controller First Before Open The EleksROM



Step2:

When EleksROM Initialization Complete . Just Choose Which EleksMaker Machine You Are Using And Click On That one IMG (EleksDraw && EleksDrawPro using the same option And you dont needed to choose which Controller you are using )



Step3:

Then You Can Choose The SerialPort Which Your Machine Is Using And Clik Connect SerialPort.



Step 4: Then You Just Need Click To DownLoad Button To Automaticlly Download and set param for your Controller.






From Now , You Dont Need To Click Anything And Just Wait a Few Minute.

Do Not UnPlug Your Controller Out At This Time , It May Broke Your Controller.



FirmWare Downloading is accomplish at this time.



Please Wait About 30s. While Controller Is Rebooting.



Now Controller Is Set Param Automaticlly.



All DownLoad Completed , Just Plug Out Your Machine And SoftWare Will Closed Automaticlly. Thanks For Choosing Our Products.

EleksROM Release V3.8.0 Update Log :


Hi , Thx For Purchase Our Products

Now we bring Brand New CoreXY/XY 丨 Laser/Servo Mode Easy Switch Firmware For You

EleksRom V3.7 Instruction
In this version , you can just type one line Gcode to the controller to switch system mode.
A0 Laser Mode
A1 Servo Mode
C0 XY Machine Mode
C1 CoreXY Machine Mode
E1 EleksLaser  Default: 80/80/Laser Mode/XY Machine Mode //x,y step/mm /Model /Machine Type
E2 EleksDraw   Default: 100/100/Servo Mode/CoreXY Machine Mode //x,y step/mm /Model /Machine Type
E3 EleksEgg    Default: 20/20/Servo Mode/XY Machine Mode //x,y step/mm /Model /Machine Type
E4 EleksMill   Default: 400/400/400/Laser Mode/XY Machine Mode //x,y,z step/mm /Model /Machine Type
All Machine Default Acceleration is 200, you can type this in Gcode Sender to change the Acceleration:
$120=500(or whatever acceleration you want) //X Axis
$121=500(or whatever acceleration you want) //Y Axis
$122=500(or whatever acceleration you want) //Z Axis

For EleksCAM you can send Gcode Here:

For Candle you can send Gcode Here:

Please Attention - The Following HardWare  Support This SoftWare 

Supported Machine:

EleksLaser A3  (Laser Power : 500mw/1600mw/2500mw/5500mw/7000mw)
EleksLaser A5  (Laser Power : 500mw/1600mw/2500mw/5500mw/7000mw)
EleksDraw  (With Draw module or Laser Power : None/500mw/1600mw/2500mw/5500mw/7000mw)
EleksDrawPro  (With Draw module or Laser Power : None/500mw/1600mw/2500mw/5500mw/7000mw)
EleksMill  (With Moter module or Laser Power : None/500mw)
EleksEgg  (With Draw module)
  • Show pagesource